Southwestern Industrial Fasteners
924 Tony Lama | El Paso, TX 79915 | (915) 592-5859
1-Cap Screw
An externally threaded fastener normally used in a tapped or blind hole to hold components together. Cap screws are distinguished from bolts by a washer face on the underside of the head and a header point. Cap screws are used when the assembly requires a stronger, more precise and better appearing fastener. During manufacturing, cap screws are held too much closer tolerances than machine bolts and are produced with semi-finished (machined) bearing surface.
2-Bolt
An externally threaded fastener normally tightened or released by torquing a nut. “Designed to hold components together”
3-Header Point
A reduction at the threaded end of a fastener designed to facilitate starting in a tapped hole.
4-Carbon Steel
Any steel made by combining carbon with iron. The amount of carbon, expressed as a percent determines whether the steel is low, medium or high carbon.
5-Heat Treating
Heating and cooling a metal in certain time cycles to obtain specific desirable conditions or properties.
6-Clamping Force
The amount of tension force created that holds two or more pieces together when a fastener is tightened. To prevent failure due to loosening, overloading, or fatigue, the clamping force produced must be greater than the external forces applied to that assembly, also defined as preload.
7-Elastic Limit
The maximum stress that can be applied to a fastener that will allow it to regain its original dimensions after removal. It is the maximum stress that can be applied with no significant measurable after effects. Once this value has been exceeded for a fastener, the fastener becomes permanently elongated and will not return to its original dimensions.
8-Proof Load
The load just under the yield strength that can be applied to a bolt with out causing permanent set greater than .0005”. This is the maximum SAFE load that the bolt can support. Torque value is established taking proof load into consideration.
9-Yield Strength
The load “usually expressed in psi” that is necessary to stretch a fastener to the point where, after the load is removed, the fastener will not return to its previous length.
10-Tension
A load that is applied in line with the center line of a bolt that stretches it.
11-Tensile Strength
The load in pounds per square inch (psi) required to cause failure in tension (stretch).
12-Shear
Force exerted 90 degrees to the center line or length of the bolt that tends to cut the bolt into two or more pieces.
13-Shear Strength
The amount of force usually expressed in psi required to shear the bolt into pieces. This is referred to as single shear and usually has a value of about 67% tensile strength. Double shear is where shearing forces are applied at two points along the shank of the body cutting the bolt into three pieces. Double shear strength is usually about 175% of tensile strength.
14-Annealing
Annealing is a heat treatment process of relatively slow cooling after holding the material at the annealing temperature for one hour for each inch of the maximum section being treated.
15-Tempering
A secondary heat treatment process used on already hardened alloy steels in order to reduce the hardness and brittleness and increase the toughness. In general as hardness is reduced so is the tensile strength but the ductility is raised.
16-Quenching
The rapid cooling of a heated metal by bringing it into contact with liquids, solids or gases.
17-Root
The deepest point of the V – notch that forms the groove of a thread, a well designed fastener should incorporate a radiused or rounded root.
18-Minor Diameter
Smallest diameter of a screw thread, “the distance across the base or root of the threads of a bolt”
19-Major Diameter
Largest diameter of a screw thread, “the distance across the crest or top of the threads on a bolt”
20-Pitch Diameter
The diameter half way between the major and minor diameters.
21-Pitch
The number of threads in one inch of the threaded length of a fastener, expressed as threads per inch (TPI). The pitch of one thread is the distance that a nut would advance on a bolt when turned one full turn. In metrics the pitch is determined by measuring the distance between the crest of one thread to the adjacent thread, this value is expressed in millimeters (mm).
An externally threaded fastener normally used in a tapped or blind hole to hold components together. Cap screws are distinguished from bolts by a washer face on the underside of the head and a header point. Cap screws are used when the assembly requires a stronger, more precise and better appearing fastener. During manufacturing, cap screws are held too much closer tolerances than machine bolts and are produced with semi-finished (machined) bearing surface.
2-Bolt
An externally threaded fastener normally tightened or released by torquing a nut. “Designed to hold components together”
3-Header Point
A reduction at the threaded end of a fastener designed to facilitate starting in a tapped hole.
4-Carbon Steel
Any steel made by combining carbon with iron. The amount of carbon, expressed as a percent determines whether the steel is low, medium or high carbon.
5-Heat Treating
Heating and cooling a metal in certain time cycles to obtain specific desirable conditions or properties.
6-Clamping Force
The amount of tension force created that holds two or more pieces together when a fastener is tightened. To prevent failure due to loosening, overloading, or fatigue, the clamping force produced must be greater than the external forces applied to that assembly, also defined as preload.
7-Elastic Limit
The maximum stress that can be applied to a fastener that will allow it to regain its original dimensions after removal. It is the maximum stress that can be applied with no significant measurable after effects. Once this value has been exceeded for a fastener, the fastener becomes permanently elongated and will not return to its original dimensions.
8-Proof Load
The load just under the yield strength that can be applied to a bolt with out causing permanent set greater than .0005”. This is the maximum SAFE load that the bolt can support. Torque value is established taking proof load into consideration.
9-Yield Strength
The load “usually expressed in psi” that is necessary to stretch a fastener to the point where, after the load is removed, the fastener will not return to its previous length.
10-Tension
A load that is applied in line with the center line of a bolt that stretches it.
11-Tensile Strength
The load in pounds per square inch (psi) required to cause failure in tension (stretch).
12-Shear
Force exerted 90 degrees to the center line or length of the bolt that tends to cut the bolt into two or more pieces.
13-Shear Strength
The amount of force usually expressed in psi required to shear the bolt into pieces. This is referred to as single shear and usually has a value of about 67% tensile strength. Double shear is where shearing forces are applied at two points along the shank of the body cutting the bolt into three pieces. Double shear strength is usually about 175% of tensile strength.
14-Annealing
Annealing is a heat treatment process of relatively slow cooling after holding the material at the annealing temperature for one hour for each inch of the maximum section being treated.
15-Tempering
A secondary heat treatment process used on already hardened alloy steels in order to reduce the hardness and brittleness and increase the toughness. In general as hardness is reduced so is the tensile strength but the ductility is raised.
16-Quenching
The rapid cooling of a heated metal by bringing it into contact with liquids, solids or gases.
17-Root
The deepest point of the V – notch that forms the groove of a thread, a well designed fastener should incorporate a radiused or rounded root.
18-Minor Diameter
Smallest diameter of a screw thread, “the distance across the base or root of the threads of a bolt”
19-Major Diameter
Largest diameter of a screw thread, “the distance across the crest or top of the threads on a bolt”
20-Pitch Diameter
The diameter half way between the major and minor diameters.
21-Pitch
The number of threads in one inch of the threaded length of a fastener, expressed as threads per inch (TPI). The pitch of one thread is the distance that a nut would advance on a bolt when turned one full turn. In metrics the pitch is determined by measuring the distance between the crest of one thread to the adjacent thread, this value is expressed in millimeters (mm).
